Where you install or place your thermostat depends on which thermostat you have and whether you’re installing it on a wall or placing it on a stand. There are also a handful of settings that you should check out, so take the time to explore the app and check out our guide to programming the Nest to get acquainted. Moving your thermostat closer to the edge of a table is fine, but moving the stand across the room or to another room can confuse your thermostat. You may also look into wearing some gloves, but you don’t need to if you shut the power off correctly.

Nest Thermostat Plate - Etsy UK Nest Thermostat Plate - Etsy UK

From there, use a pencil and mark where the two screws need to go--one on the top and one on the bottom. The thermostat’s compatibility checker will tell you if a C-wire connection is needed to power the device up. If you’re planning to reuse your Nest thermostat, remember to keep all of its components in a sealed container. At this point, you can adjust the temperature of your Nest Thermostat right from your phone and from anywhere in the world. Also note that it may be against the law, code, or regulations to do this without a permit, or it might void your insurance or warranty.If you noticed that the thermostat is not working, check on those connections and see if they were made properly. If it reads something like "110 VAC", "115 VAC", or "120 VAC", then you have a high-voltage system and the Nest won't work. If you’re still getting voltage readings, go back to your breaker box and look for the right breaker again. Note:Only one of the wires that go into theconnector (HUM,DEHUM,E,W 3,G 3) can be connected to the Nest thermostat. When you're ready to drive in the screws (a drill is highly recommended for this), place the base plate back on the wall where you want it and feed the wires through the center hole (include the trim plate behind the base plate if you want--it's good to use if you don't want to spackle and paint over the spot where the old thermostat was).

Nest Thermostat Wall Plate - Etsy

If you have a dual fuel system or a whole-home humidifier/dehumidifier, it is strongly recommended that you choose professional installation. Note: Occasional sunlight is fine since your Nest thermostat’s Sunblock feature can help adjust the temperature, based on irregular heat spikes and patterns. We are experiencing extremely high contact volume right now and estimated wait times will be higher than normal. Because Nest Learning Thermostats sometimes require changes to the thermostat wiring, it’s recommended that you have yours professionally installed to keep you safe and avoid damaging your system or thermostat.Removing one from the wall is easier than it looks as long as you shut it down safely before you remove it from the base. Before you even get started on removing the Nest thermostat, you will first have to perform a factory reset.

Nest Thermostat Wall Plates - Etsy Nest Thermostat Wall Plates - Etsy

You might think that the Nest Thermostat will work with any thermostat setup in any home, but that's not quite the case. The Nest Learning Thermostat works with 95% of 24 V heating and cooling systems, including gas, electric, forced air, heat pump, radiant, oil, hot water, solar and geothermal. If you need to replace the power cable, you can use a standard micro USB cable for 3rd or 2nd gen Nest Learning Thermostats. A smart thermostat is a great accessory to have, not only to be able to adjust your home's temperature from your phone, but to also save money on your utility costs.Contact our installation partner, OnTech, to help you check your system’s compatibility, install, and set up your Nest products. If you purchase a Nest thermostat from a pro and have them install it, you can also get an extended Pro Warranty. Once you’ve set up your thermostat and connected it to the Nest app, follow the link below to learn about how to use your Nest thermostat. For complete details about where to place your thermostat, please see Where to place your Nest thermostat.

Nest Thermostat Wall Plate, 6 Inch, Bamboo Plate, Fits

Nest screws are self-tapping, so there’s no need to drill into soft materials like drywall or plaster. Most of the time, the color of the wire will correctly correspond to the letter of the screw that it's connected to (e. The thermostat only tells the system when to turn on or off, so the system needs to be connected to your home’s power. The Nest app’s step-by-step instructions make it easy to install and wire your thermostat, so use it as your main guide.

If you’re not sure which model you have, go to our article about How to tell which Nest thermostat you have.